" DISCLAIMER: The ILO does not take responsibility for content presented on this web portal that is presented in any language other than English, which is the language used for the initial production and peer-review of original content. Certain statistics have not been updated since the production of the 4th edition of the Encyclopaedia (1998)."

Monday, 28 March 2011 20:15

Sheet Production and Converting: Market Pulp, Paper, Paperboard

Written by
Rate this item
(1 Vote)

End products of pulp and paper mills depend on the pulping process, and may include market pulp and various types of paper or paperboard products. For example, the relatively weak mechanical pulp is converted into single-use products such as newspapers and tissue. Kraft pulp is converted into multi-use paper products such as high-quality writing paper, books and grocery bags. Sulphite pulp, which is primarily cellulose, can be used in a series of diverse end-products including specialty paper, rayon, photographic film, TNT, plastics, adhesives, and even ice cream and cake mixes. Chemi-mechanical pulps are exceptionally stiff, ideal for the structural support needed for corrugated container board. The fibres in pulp from recycled paper are usually shorter, less flexible and less water permeable, and can therefore not be used for high-quality paper products. Recycled paper is therefore mainly used for the production of soft paper products like tissue paper, toilet paper, paper towelling and napkins.

To produce market pulp, the pulp slurry is usually screened once more and its consistency adjusted (4 to 10%) before it is ready for the pulp machine. The pulp is then spread onto a travelling metal screen or plastic mesh (known as the “wire”) at the “wet end” of the pulp machine, where the operator monitors the speed of the moving wire and the water content of the pulp (figure 1; the presses and the cover of the drier can be seen in the upper left; in modern mills, operators spend a great deal of time in control rooms). Water and filtrate are drawn through the wire, leaving a web of fibres. The pulp sheet is passed through a series of rotating rolls (“presses”) that squeeze out water and air until the fibre consistency is 40 to 45%. The sheet is then floated through a multi-storey sequence of hot-air dryers until the consistency is 90 to 95%. Finally, the continuous pulp sheet is cut into pieces and stacked into bales. The pulp bales are compressed, wrapped and packaged into bundles for storage and transport.

Figure 1. Wet end of pulp machine showing fibre mat on the wire.

PPI070F1

Canfor Library

Although similar in principle to making pulp sheets, paper making is considerably more complex. Some mills use a variety of different pulps to optimize paper quality (e.g., a mix of hardwood, softwood, kraft, sulphite, mechanical or recycled pulps). Depending on the type of pulp used, a series of steps is necessary prior to forming the paper sheet. Generally, dried market pulp is rehydrated, while high-consistency pulp from storage is diluted. Pulp fibres may be beaten to increase the fibre-bonding area and thereby improve paper sheet strength. The pulp is then blended with “wet-end” additives (table 1) and passed through a final set of screens and cleaners. The pulp is then ready for the paper machine.

Table 1. Papermaking additives

Additive

Location applied

Purpose and/or examples of specific agents

Most commonly used additives

Talc

Wet end

Pitch control (prevent deposition and accumulation
of pitch)
Filler (make brighter, smoother, more opaque)

Titanium dioxide

Wet end

Pigment (brighten sheet, improve printing)
Filler (make brighter, smoother, more opaque)

“Alum”(Al2(SO4)3)

Wet end

Precipitates rosin sizing onto fibres
Retention aid (fix additives to fibres, improve pulp
fibre retention)

Rosin

Wet end

Internal sizing (resist liquid penetration)

Clay (kaolin)

Wet/dry

Filler (make brighter, smoother, more opaque)
Pigment or surface coating (impart colour)

Starch

Wet/dry

Surface sizing (resist liquid penetration)
Dry strength additive (increase strength, reduce
surface lint)
Retention aid (bind additives to paper, improve
pulp fibre retention)

Dyes and
pigments

Wet/dry

e.g., acid, basic or direct dyes,colour lakes,
CaCO3, may also include solvent vehicles

Latex

Dry end

Adhesive (reinforce sheet, bind additives to paper,
fill pores)
Waterproofing (resist liquid penetration)

Other additives

Slimicides

Wet end

e.g., thiones, thiazoles, thiocyanates, hiocarbamates, thiols, isothiazolinones,
formaldehyde, glutaraldehyde, glycols, naphthol,
chlorinated and brominated organics, organic
mercury compounds

Defoamers

Wet end

e.g., pine oil, fuel oil, recycled oils, silicones, alcohols

Wire treatment
agents

Wet end

e.g., imidazoles, butyl diglycol, acetone, turpentine,
phosphoric acid

Wet and dry
strength additives

Wet end

e.g., formaldehyde resins, epichlorohydrin, glyoxal,
gums, polyamines, phenolics,
polyacrylamides, polyamids, cellulose derivatives

Coatings,
adhesives and
plasticizers

Dry end

e.g., aluminium hydroxide, polyvinyl acetate,
acrylics, linseed oil, gums, protein glues, wax
emulsions, azite, glyoxal, stearates, solvents,
polyethylene, cellulose derivatives, foil, rubber
derivatives, polyamines, polyesters,
butadiene-styrene polymers

Others

Wet/dry

Corrosion inhibitors, dispersants, flameproofing,
antitarnish agents, drainage aids, deflocculants, pH
control agents, preservatives

 

The flow spreader and headbox distribute a thin suspension (1 to 3%) of refined pulp onto a moving wire (similar to a pulp machine, only at a much higher speed, sometimes in excess of 55 km/h) which forms the fibres into a thin felted sheet. The sheet moves through a series of press rolls to the dryer section, where a series of steam-heated rolls evaporate most of the remaining water. Hydrogen bonds between the fibres have fully developed at this stage. Finally, the paper is calendered and reeled. Calendering is the process by which the paper surface is ironed smooth and its thickness reduced. The dried, calendered paper sheet is wound onto a reel, labelled and transported to the warehouse (figure 2; note waste paper under reel, and unenclosed operator control panel). “Dry-end” additives can be added before calendering on the paper machine or in separate “off-machine” coating operations in the converting sector of the industry.

Figure 2. Dry end of a paper machine showing full paper reel and operator using air slitter to cut end.

PPI070F2

George Astrakianakis

A variety of chemicals are used in the papermaking process to provide the paper with specific surface characteristics and sheet properties. The most commonly used additives (table 1) are typically used at the per cent level, though some such as clay and talc may contribute as much as 40% to the dry weight of certain papers. Table 1 also indicates the diversity of chemical additives which may be used for specific production purposes and products; some of these are used at very low concentrations (e.g., slimicides are added to process water in parts per million).

The process of making paperboard is similar to that of making paper or pulp. A suspension of pulp and water is dispersed onto a travelling wire, the water is removed, and the sheet dried and stored as a roll. The process differs in the way that the sheet is formed to give thickness, in the combining of multiple layers, and in the drying process. Board can be made from single or multi-layered sheets with or without a core. The sheets are usually high-quality kraft pulp (or kraft and CTMP blend), while the core is made from either a blend of semi-chemical and low-cost recycled pulp or from entirely recycled pulp and other waste material. Coatings, vapour barriers and multiple layers are added according to the end use to protect the contents from water and physical damage.

 

Back

Read 5743 times Last modified on Saturday, 27 August 2011 17:25

Contents

Preface
Part I. The Body
Part II. Health Care
Part III. Management & Policy
Part IV. Tools and Approaches
Part V. Psychosocial and Organizational Factors
Part VI. General Hazards
Part VII. The Environment
Part VIII. Accidents and Safety Management
Part IX. Chemicals
Part X. Industries Based on Biological Resources
Agriculture and Natural Resources Based Industries
Beverage Industry
Fishing
Food Industry
Forestry
Hunting
Livestock Rearing
Lumber
Paper and Pulp Industry
Major Sectors and Processes
Disease and Injury Patterns
Resources
Part XI. Industries Based on Natural Resources
Part XII. Chemical Industries
Part XIII. Manufacturing Industries
Part XIV. Textile and Apparel Industries
Part XV. Transport Industries
Part XVI. Construction
Part XVII. Services and Trade
Part XVIII. Guides

Paper and Pulp Industry Additional Resources

Click the Button below to view additional resources for this topic.

button

Paper and Pulp Industry References

Canadian Pulp and Paper Association. 1995. Reference Tables 1995. Montreal, PQ: CPPA.

Food and Agriculture Organization (FAO) of the United Nations. 1995. Pulp and Paper Capacities, Survey 1994-1999. Rome: FAO.

Henneberger, PK, JR Ferris, and RR Monson. 1989. Mortality among pulp and paper workers in Berlin. Br J Ind Med 46:658-664.

International Agency on the Research of Cancer (IARC). 1980. Monographs on the Evaluation of Carcinogenic Risks to Humans: Wood, Leather and Some Associated Industries. Vol. 25. Lyon: IARC.

—.1987. Monographs on the Evaluation of Carcinogenic Risks to Humans, Overall Evaluations of Carcinogenicity: An Updating of IARC Monographs. Vol. 1-42 (supplement 7). Lyon: IARC.

—.1995. Monographs on the Evaluation of Carcinogenic Risks to Humans: Wood Dust and Formaldehyde. Vol. 62. Lyon: IARC.

International Labour Organization (ILO). 1992. Social and Labour Issues in the Pulp and Paper Industry. Geneva: ILO.

Jäppinen, P. 1987. Exposure to Compounds, Cancer Incidence and Mortality in the Finnish Pulp and Paper Industry. Thesis, Helsingfors, Finland.

Jäppinen, P and S Tola. 1990. Cardiovascular mortality among pulp mill workers. Br J Ind Med 47:259-261.

Jäppinen, P, T Hakulinen, E Pukkala, S Tola, and K Kurppa. 1987. Cancer incidence of workers in the Finnish pulp and paper industry. Scand J Work Environ Health 13:197-202.

Johnson, CC, JF Annegers, RF Frankowski, MR Spitz, and PA Buffler. 1987. Childhood nervous system tumors—An evaluation of the association with paternal occupational exposure to hydrocarbons. Am J Epidemiol 126:605-613.

Kuijten, R, GR Bunin, and CC Nass. 1992. Parental occupation and childhood astrocytoma: Results of a case-control study. Cancer Res 52:782-786.

Kwa, SL and IJ Fine. 1980. The association between parental occupation and childhood malignancy. J Occup Med 22:792-794.

Malker, HSR, JK McLaughlin, BK Malker, NJ Stone, JA Weiner, JLE Ericsson, and WJ Blot. 1985. Occupational risks for pleural mesothelioma in Sweden, 1961-1979. J Natl Cancer Inst 74:61-66.

—. 1986. Biliary tract cancer and occupation in Sweden. Br J Ind Med 43:257-262.

Milham, SJ. 1976. Neoplasias in the wood and pulp industry. Ann NY Acad Sci 271:294-300.

Milham, SJ and P Demers. 1984. Mortality among pulp and paper workers. J Occup Med 26:844-846.

Milham, SJ and J Hesser. 1967. Hodgkin’s disease in woodworkers. Lancet 2:136-137.

Nasca, P, MS Baptiste, PA MacCubbin, BB Metzger, K Carton, P Greenwald, and VW Armbrustmacher. 1988. An epidemiologic case-control study of central nervous system tumors in children and parental occupational exposures. Am J Epidemiol 128:1256-1265.

Persson, B, M Fredriksson, K Olsen, B Boeryd, and O Axelson. 1993. Some occupational exposures as risk factors for malignant melanomas. Cancer 72:1773-1778.

Pickle, L and M Gottlieb. 1980. Pancreatic cancer mortality in Louisiana. Am J Public Health 70:256-259.
Pulp and Paper International (PPI). 1995. Vol. 37. Brussels: Miller Freeman.

Robinson, C, J Waxweiller, and D Fowler. 1986. Mortality among production workers in pulp and paper mills. Scand J Work Environ Health 12:552-560.


Schwartz, B. 1988. A proportionate mortality ratio analysis of pulp and paper mill workers in New Hampshire. Br J Ind Med 45:234-238.

Siemiatycki, J, L Richardson, M Gérin, M Goldberg, R Dewar, M Désy, S Campell, and S Wacholder. 1986. Association between several sites of cancer and nine organic dusts: Results from an hypothesis-generating case control study in Montreal, 1979-1983. Am J Epidemiol 123:235-249.

Skalpe, IO. 1964. Long-term effects of sulfur dioxide exposure in pulp mills. Br J Ind Med 21:69-73.

Solet, D, R Zoloth, C Sullivan, J Jewett, and DM Michaels. 1989. Patterns of mortality in pulp and paper workers. J Occup Med 31:627-630.

Torén, K, S Hagberg, and H Westberg. 1996. Health effects of working in pulp and paper mills: Exposure, obstructive airways diseases, hypersensitivity reactions, and cardiovascular diseases. Am J Ind Med 29:111-122.

Torén, K, B Järvholm, and U Morgan. 1989. Mortality from asthma and chronic obstructive pulmonary diseases among workers in a soft paper mill: A case referent study. Br J Ind Med 46:192-195.

Torén, K, B Persson, and G Wingren. 1996. Health effects of working in pulp and paper mills: Malignant diseases. Am J Ind Med 29:123-130.

Torén, K, G. Sällsten, and B Järvholm. 1991. Mortality from asthma, chronic obstructive pulmonary disease, respiratory system cancer among paper mill workers: A case referent study. Am J Ind Med 19:729-737.

US Department of Commerce. 1983. Pulp and Paper Mills. (PB 83-115766). Washington, DC: US Department of Commerce.

—.1993. Selected Occupational Fatalities Related to Pulp Paper and Paperboard Mills as Found in Reports of OSHA Fatality/Catastrophe Investigations. (PB93-213502). Washington, DC: US Department of Commerce.

Weidenmüller, R. 1984. Papermaking, the Art and Craft of Handmade Paper. San Diego, CA: Thorfinn International Marketing Consultants Inc.

Wingren, G, H Kling, and O Axelson. 1985. Gastric cancer among paper mill workers. J Occup Med 27:715.

Wingren, G, B Persson, K Torén, and O Axelson. 1991. Mortality patterns among pulp and paper mill workers in Sweden: A case-referent study. Am J Ind Med 20:769-774.

Workers’ Compensation Board of British Columbia. 1995. Personal communication.