Monday, 04 April 2011 19:04

Falls from Elevations

Rate this item
(1 Vote)

Falls from elevations are severe accidents that occur in many industries and occupations. Falls from elevations result in injuries which are produced by contact between the falling person and the source of injury, under the following circumstances:

  • The motion of the person and the force of impact are generated by gravity.
  • The point of contact with the source of injury is lower than the surface supporting the person at the start of the fall.

 

From this definition, it may be surmised that falls are unavoidable because gravity is always present. Falls are accidents, somehow predictable, occurring in all industrial sectors and occupations and having a high severity. Strategies to reduce the number of falls, or at least reduce the severity of the injuries if falls occur, are discussed in this article.

The Height of the Fall

The severity of injuries caused by falls is intrinsically related to the height of fall. But this is only partly true: the free-fall energy is the product of the falling mass times the height of the fall, and the severity of the injuries is directly proportional to the energy transferred during the impact. Statistics of fall accidents confirm this strong relationship, but show also that falls from a height of less than 3 m can be fatal. A detailed study of fatal falls in construction shows that 10% of the fatalities caused by falls occurred from a height less than 3 m (see figure 1). Two questions are to be discussed: the 3-m legal limit, and where and how a given fall was arrested.

Figure 1. Fatalities caused by falls and the height of fall in the US construction industry, 1985-1993

ACC080T1

In many countries, regulations make fall protection mandatory when the worker is exposed to a fall of more than 3 m. The simplistic interpretation is that falls of less than 3 m are not dangerous. The 3-m limit is in fact the result of a social, political and practical consensus which says it is not mandatory to be protected against falls while working at the height of a single floor. Even if the 3-m legal limit for mandatory fall protection exists, fall protection should always be considered. The height of fall is not the sole factor explaining the severity of fall accidents and the fatalities due to falls; where and how the person falling came to rest must also be considered. This leads to analysis of the industrial sectors with higher incidence of falls from elevations.

Where Falls Occur

Falls from elevations are frequently associated with the construction industry because they account for a high percentage of all fatalities. For example, in the United States, 33% of all fatalities in construction are caused by falls from elevations; in the UK, the figure is 52%. Falls from elevations also occur in other industrial sectors. Mining and the manufacturing of transportation equipment have a high rate of falls from elevations. In Quebec, where many mines are steep, narrow-vein, underground mines, 20% of all accidents are falls from elevations. The manufacture, use and maintenance of transportation equipment such as airplanes, trucks and railroad cars are activities with a high rate of fall accidents (table 1). The ratio will vary from country to country depending on the level of industrialization, the climate, and so on; but falls from elevations do occur in all sectors with similar consequences.


Table 1. Falls from elevations: Quebec 1982-1987

                               Falls from elevations                         Falls from elevations in all accidents
                               per 1,000 workers

Construction                        14.9                                                10.1%

Heavy industry                      7.1                                                  3.6%


Having taken into consideration the height of fall, the next important issue is how the fall is arrested. Falling into hot liquids, electrified rails or into a rock crusher could be fatal even if the height of fall is less than 3 m.

Causes of Falls

So far it has been shown that falls occur in all economic sectors, even if the height is less than 3 m. But why do humans fall? There are many human factors which can be involved in falling. A broad grouping of factors is both conceptually simple and useful in practice:

Opportunities to fall are determined by environmental factors and result in the most common type of fall, namely the tripping or slipping that result in falls from grade level. Other falling opportunities are related to activities above grade.

Liabilities to fall are one or more of the many acute and chronic diseases. The specific diseases associated with falling usually affect the nervous system, the circulatory system, the musculoskeletal system or a combination of these systems.

Tendencies to fall arise from the universal, intrinsic deteriorative changes that characterize normal ageing or senescence. In falling, the ability to maintain upright posture or postural stability is the function that fails as a result of combined tendencies, liabilities and opportunities.

Postural Stability

Falls are caused by the failure of postural stability to maintain a person in an upright position. Postural stability is a system consisting of many rapid adjustments to external, perturbing forces, especially gravity. These adjustments are largely reflex actions, subserved by a large number of reflex arcs, each with its sensory input, internal integrative connections, and motor output. Sensory inputs are: vision, the inner ear mechanisms that detect position in space, the somatosensory apparatus that detects pressure stimuli on the skin, and the position of the weight-bearing joints. It appears that visual perception plays a particularly important role. Very little is known about the normal, integrative structures and functions of the spinal cord or the brain. The motor output component of the reflex arc is muscular reaction.

Vision

The most important sensory input is vision. Two visual functions are related to postural stability and control of gait:

  • the perception of what is vertical and what is horizontal is basic to spatial orientation
  • the ability to detect and discriminate objects in cluttered environments.

 

Two other visual functions are important:

  • the ability to stabilize the direction in which the eyes are pointed so as to stabilize the surrounding world while we are moving and immobilize a visual reference point
  • the ability to fixate and pursue definite objects within the large field (“keep an eye on”); this function requires considerable attention and results in deterioration in the performance of any other simultaneous, attention-demanding tasks.

 

Causes of postural instability

The three sensory inputs are interactive and interrelated. The absence of one input—and/or the existence of false inputs—results in postural instability and even in falls. What could cause instability?

Vision

  • the absence of vertical and horizontal references—for example, the connector at the top of a building
  • the absence of stable visual references—for example, moving water under a bridge and moving clouds are not stable references
  • the fixing a definite object for work purposes, which diminishes other visual functions, such as the ability to detect and discriminate objects that can cause tripping in a cluttered environment
  • a moving object in a moving background or reference—for example, a structural steel component moved by a crane, with moving clouds as background and visual reference.

 

Inner ear

  • having the person’s head upside down while the level equilibrium system is at its optimum performance horizontally
  • travelling in pressurized aircraft
  • very fast movement, as, for example, in a roller-coaster
  • diseases.

 

Somatosensory apparatus (pressure stimuli on the skin and position of weight-bearing joints)

  • standing on one foot
  • numbed limbs from staying in a fixed position for a long period of time—for example, kneeling down
  • stiff boots
  • very cold limbs.

 

Motor output

  • numbed limbs
  • tired muscles
  • diseases, injuries
  • ageing, permanent or temporary disabilities
  • bulky clothing.

 

Postural stability and gait control are very complex reflexes of the human being. Any perturbations of the inputs may cause falls. All perturbations described in this section are common in the workplace. Therefore, falling is somehow natural and prevention must therefore prevail.

Strategy for Fall Protection

As previously noted, the risks of falls are identifiable. Therefore, falls are preventable. Figure 2 shows a very common situation where a gauge must be read. The first illustration shows a traditional situation: a manometer is installed at the top of a tank without means of access In the second, the worker improvises a means of access by climbing on several boxes: a hazardous situation. In the third, the worker uses a ladder; this is an improvement. However, the ladder is not permanently fixed to the tank; it is therefore probable that the ladder may be in use elsewhere in the plant when a reading is required. A situation such as this is possible, with fall arrest equipment added to the ladder or the tank and with the worker wearing a full body harness and using a lanyard attached to an anchor. The fall-from-elevation hazard still exists.

Figure 2. Installations for reading a gauge

ACC080F1

In the fourth illustration, an improved means of access is provided using a stairway, a platform and guardrails; the benefits are a reduction in the risk of falling and an increase in the ease of reading (comfort), thus reducing the duration of each reading and providing a stable work posture allowing for a more precise reading.

The correct solution is illustrated in the last illustration. During the design stage of the facilities, maintenance and operation activities were recognized. The gauge was installed so that it could be read at ground level. No falls from elevations are possible: therefore, the hazard is eliminated.

This strategy puts the emphasis on the prevention of falls by using the proper means of access (e.g., scaffolds, ladders, stairways) (Bouchard 1991). If the fall cannot be prevented, fall arrest systems must be used (figure 3). To be effective, fall arrest systems must be planned. The anchorage point is a key factor and must be pre-engineered. Fall arrest systems must be efficient, reliable and comfortable; two examples are given in Arteau, Lan and Corbeil (to be published) and Lan, Arteau and Corbeil (to be published). Examples of typical fall prevention and fall arrest systems are given in table 2. Fall arrest systems and components are detailed in Sulowski 1991.

Figure 3. Fall prevention strategy

ACC080F6

 

Table 2. Typical fall prevention and fall arrest systems

 

Fall prevention systems

Fall arrest systems

Collective protection

Guardrails Railings

Safety net

Individual protection

Travel restricting system (TRS)

Harness, lanyard, energy absorber anchorage, etc.

 

The emphasis on prevention is not an ideological choice, but rather a practical choice. Table 3 shows the differences between fall prevention and fall arrest, the traditional PPE solution.

Table 3. Differences between fall prevention and fall arrest

 

Prevention

Arrest

Fall occurrence

No

Yes

Typical equipment

Guardrails

Harness, lanyard, energy absorber and anchorage (fall arrest system)

Design load (force)

1 to 1.5 kN applied horizontally and 0.45 kN applied vertically—both at any point on the upper rail

Minimum breaking strength of the anchorage point

18 to 22 kN

Loading

Static

Dynamic

 

For the employer and the designer, it is easier to build fall prevention systems because their minimum breaking strength requirements are 10 to 20 times less than those of fall arrest systems. For example, the minimum breaking strength requirement of a guard rail is around 1 kN, the weight of a large man, and the minimum breaking strength requirement of the anchorage point of an individual fall arrest system could be 20 kN, the weight of two small cars or 1 cubic metre of concrete. With prevention, the fall does not occur, so the risk of injury does not exist. With fall arrest, the fall does occur and even if arrested, a residual risk of injury exists.

 

Back

Read 7783 times Last modified on Saturday, 20 August 2011 19:40
More in this category: « Rollover Confined Spaces »

" DISCLAIMER: The ILO does not take responsibility for content presented on this web portal that is presented in any language other than English, which is the language used for the initial production and peer-review of original content. Certain statistics have not been updated since the production of the 4th edition of the Encyclopaedia (1998)."

Contents

Safety Applications References

Arteau, J, A Lan, and J-F Corveil. 1994. Use of Horizontal Lifelines in Structural Steel Erection. Proceedings of the International Fall Protection Symposium, San Diego, California (October 27–28, 1994). Toronto: International Society for Fall Protection.

Backström, T. 1996. Accident risk and safety protection in automated production. Doctoral thesis. Arbete och Hälsa 1996:7. Solna: National Institute for Working Life.

Backström, T and L Harms-Ringdahl. 1984. A statistical study of control systems and accidents at work. J Occup Acc. 6:201–210.

Backström, T and M Döös. 1994. Technical defects behind accidents in automated production. In Advances in Agile Manufacturing, edited by PT Kidd and W Karwowski. Amsterdam: IOS Press.

—. 1995. A comparison of occupational accidents in industries with of advanced manufacturing technology. Int J Hum Factors Manufac. 5(3). 267–282.

—. In press. The technical genesis of machine failures leading to occupational accidents. Int J Ind Ergonomics.

—. Accepted for publication. Absolute and relative frequencies of automation accidents at different kinds of equipment and for different occupational groups. J Saf Res.

Bainbridge, L. 1983. Ironies of automation. Automatica 19:775–779.

Bell, R and D Reinert. 1992. Risk and system integrity concepts for safety related control systems. Saf Sci 15:283–308.

Bouchard, P. 1991. Échafaudages. Guide série 4. Montreal: CSST.

Bureau of National Affairs. 1975. Occupational Safety and Health Standards. Roll-over Protective Structures for Material Handling Equipment and Tractors, Sections 1926, 1928. Washington, DC: Bureau of National Affairs.

Corbett, JM. 1988. Ergonomics in the development of human-centred AMT. Applied Ergonomics 19:35–39.

Culver, C and C Connolly. 1994. Prevent fatal falls in construction. Saf Health September 1994:72–75.

Deutsche Industrie Normen (DIN). 1990. Grundsätze für Rechner in Systemen mit Sicherheitsauffgaben. DIN V VDE 0801. Berlin: Beuth Verlag.

—. 1994. Grundsätze für Rechner in Systemen mit Sicherheitsauffgaben Änderung A 1. DIN V VDE 0801/A1. Berlin: Beuth Verlag.

—. 1995a. Sicherheit von Maschinen—Druckempfindliche Schutzeinrichtungen [Machine safety—Pressure-sensitive protective equipment]. DIN prEN 1760. Berlin: Beuth Verlag.

—. 1995b. Rangier-Warneinrichtungen—Anforderungen und Prüfung [Commercial vehicles—obstacle detection during reversing—requirements and tests]. DIN-Norm 75031. February 1995.

Döös, M and T Backström. 1993. Description of accidents in automated materials handling. In Ergonomics of Materials Handling and Information Processing at Work, edited by WS Marras, W Karwowski, JL Smith, and L Pacholski. Warsaw: Taylor and Francis.

—. 1994. Production disturbances as an accident risk. In Advances in Agile Manufacturing, edited by PT Kidd and W Karwowski. Amsterdam: IOS Press.

European Economic Community (EEC). 1974, 1977, 1979, 1982, 1987. Council Directives on Rollover Protection Structures of Wheeled Agricultural and Forestry Tractors. Brussels: EEC.

—. 1991. Council Directive on the Approximation of the Laws of the Member States relating to Machinery. (91/368/EEC) Luxembourg: EEC.

Etherton, JR and ML Myers. 1990. Machine safety research at NIOSH and future directions. Int J Ind Erg 6:163–174.

Freund, E, F Dierks and J Roßmann. 1993. Unterschungen zum Arbeitsschutz bei Mobilen Rototern und Mehrrobotersystemen [Occupational safety tests of mobile robots and multiple robot systems]. Dortmund: Schriftenreihe der Bundesanstalt für Arbeitsschutz.

Goble, W. 1992. Evaluating Control System Reliability. New York: Instrument Society of America.

Goodstein, LP, HB Anderson and SE Olsen (eds.). 1988. Tasks, Errors and Mental Models. London: Taylor and Francis.

Gryfe, CI. 1988. Causes and prevention of falling. In International Fall Protection Symposium. Orlando: International Society for Fall Protection.

Health and Safety Executive. 1989. Health and safety statistics 1986–87. Employ Gaz 97(2).

Heinrich, HW, D Peterson and N Roos. 1980. Industrial Accident Prevention. 5th edn. New York: McGraw-Hill.

Hollnagel, E, and D Woods. 1983. Cognitive systems engineering: New wine in new bottles. Int J Man Machine Stud 18:583–600.

Hölscher, H and J Rader. 1984. Mikrocomputer in der Sicherheitstechnik. Rheinland: Verlag TgV-Reinland.

Hörte, S-Å and P Lindberg. 1989. Diffusion and Implementation of Advanced Manufacturing Technologies in Sweden. Working paper No. 198:16. Institute of Innovation and Technology.

International Electrotechnical Commission (IEC). 1992. 122 Draft Standard: Software for Computers in the Application of Industrial Safety-related Systems. IEC 65 (Sec). Geneva: IEC.

—. 1993. 123 Draft Standard: Functional Safety of Electrical/Electronic/Programmable Electronic Systems; Generic Aspects. Part 1, General requirements Geneva: IEC.

International Labour Organization (ILO). 1965. Safety & Health in Agricultural Work. Geneva: ILO.

—. 1969. Safety and Health in Forestry Work. Geneva: ILO.

—. 1976. Safe Construction and Operation of Tractors. An ILO Code of Practice. Geneva: ILO.

International Organization for Standardization (ISO). 1981. Agricultural and Forestry Wheeled Tractors. Protective Structures. Static Test Method and Acceptance Conditions. ISO 5700. Geneva: ISO.

—. 1990. Quality Management and Quality Assurance Standards: Guidelines for the Application of ISO 9001 to the Development, Supply and Maintenance of Software. ISO 9000-3. Geneva: ISO.

—. 1991. Industrial Automation Systems—Safety of Integrated Manufacturing Systems—Basic Requirements (CD 11161). TC 184/WG 4. Geneva: ISO.

—. 1994. Commercial Vehicles—Obstacle Detection Device during Reversing—Requirements and Tests. Technical Report TR 12155. Geneva: ISO.

Johnson, B. 1989. Design and Analysis of Fault Tolerant Digital Systems. New York: Addison Wesley.

Kidd, P. 1994. Skill-based automated manufacturing. In Organization and Management of Advanced Manufacturing Systems, edited by W Karwowski and G Salvendy. New York: Wiley.

Knowlton, RE. 1986. An Introduction to Hazard and Operability Studies: The Guide Word Approach. Vancouver, BC: Chemetics.

Kuivanen, R. 1990. The impact on safety of disturbances in flexible manufacturing systems. In Ergonomics of Hybrid Automated Systems II, edited by W Karwowski and M Rahimi. Amsterdam: Elsevier.

Laeser, RP, WI McLaughlin and DM Wolff. 1987. Fernsteurerung und Fehlerkontrolle von Voyager 2. Spektrum der Wissenshaft (1):S. 60–70.

Lan, A, J Arteau and J-F Corbeil. 1994. Protection Against Falls from Above-ground Billboards. International Fall Protection Symposium, San Diego, California, October 27–28, 1994. Proceedings International Society for Fall Protection.

Langer, HJ and W Kurfürst. 1985. Einsatz von Sensoren zur Absicherung des Rückraumes von Großfahrzeugen [Using sensors to secure the area behind large vehicles]. FB 605. Dortmund: Schriftenreihe der bundesanstalt für Arbeitsschutz.

Levenson, NG. 1986. Software safety: Why, what, and how. ACM Computer Surveys (2):S. 129–163.

McManus, TN. N.d. Confined Spaces. Manuscript.

Microsonic GmbH. 1996. Company communication. Dortmund, Germany: Microsonic.

Mester, U, T Herwig, G Dönges, B Brodbeck, HD Bredow, M Behrens and U Ahrens. 1980. Gefahrenschutz durch passive Infrarot-Sensoren (II) [Protection against hazards by infrared sensors]. FB 243. Dortmund: Schriftenreihe der bundesanstalt für Arbeitsschutz.

Mohan, D and R Patel. 1992. Design of safer agricultural equipment: Application of ergonomics and epidemiology. Int J Ind Erg 10:301–310.

National Fire Protection Association (NFPA). 1993. NFPA 306: Control of Gas Hazards on Vessels. Quincy, MA: NFPA.

National Institute for Occupational Safety and Health (NIOSH). 1994. Worker Deaths in Confined Spaces. Cincinnati, OH, US: DHHS/PHS/CDCP/NIOSH Pub. No. 94-103. NIOSH.

Neumann, PG. 1987. The N best (or worst) computer-related risk cases. IEEE T Syst Man Cyb. New York: S.11–13.

—. 1994. Illustrative risks to the public in the use of computer systems and related technologies. Software Engin Notes SIGSOFT 19, No. 1:16–29.

Occupational Safety and Health Administration (OSHA). 1988. Selected Occupational Fatalities Related to Welding and Cutting as Found in Reports of OSHA Fatality/Catastrophe Investigations. Washington, DC: OSHA.

Organization for Economic Cooperation and Development (OECD). 1987. Standard Codes for the Official Testing of Agricultural Tractors. Paris: OECD.

Organisme professionel de prévention du bâtiment et des travaux publics (OPPBTP). 1984. Les équipements individuels de protection contre les chutes de hauteur. Boulogne-Bilancourt, France: OPPBTP.

Rasmussen, J. 1983. Skills, rules and knowledge: Agenda, signs and symbols, and other distinctions in human performance models. IEEE Transactions on Systems, Man and Cybernetics. SMC13(3): 257–266.

Reason, J. 1990. Human Error. New York: Cambridge University Press.

Reese, CD and GR Mills. 1986. Trauma epidemiology of confined space fatalities and its application to intervention/prevention now. In The Changing Nature of Work and Workforce. Cincinnati, OH: NIOSH.

Reinert, D and G Reuss. 1991. Sicherheitstechnische Beurteilung und Prüfung mikroprozessorgesteuerter
Sicherheitseinrichtungen. In BIA-Handbuch. Sicherheitstechnisches Informations-und Arbeitsblatt 310222. Bielefeld: Erich Schmidt Verlag.

Society of Automotive Engineers (SAE). 1974. Operator Protection for Industrial Equipment. SAE Standard j1042. Warrendale, USA: SAE.

—. 1975. Performance Criteria for Rollover Protection. SAE Recommended Practice. SAE standard j1040a. Warrendale, USA: SAE.

Schreiber, P. 1990. Entwicklungsstand bei Rückraumwarneinrichtungen [State of developments for rear area warning devices]. Technische Überwachung, Nr. 4, April, S. 161.

Schreiber, P and K Kuhn. 1995. Informationstechnologie in der Fertigungstechnik [Information technology in production technique, series of the Federal Institute for Occupational Safety and Health]. FB 717. Dortmund: Schriftenreihe der bundesanstalt für Arbeitsschutz.

Sheridan, T. 1987. Supervisory control. In Handbook of Human Factors, edited by G. Salvendy. New York: Wiley.

Springfeldt, B. 1993. Effects of Occupational Safety Rules and Measures with Special Regard to Injuries. Advantages of Automatically Working Solutions. Stockholm: The Royal Institute of Technology, Department of Work Science.

Sugimoto, N. 1987. Subjects and problems of robot safety technology. In Occupational Safety and Health in Automation and Robotics, edited by K Noto. London: Taylor & Francis. 175.

Sulowski, AC (ed.). 1991. Fundamentals of Fall Protection. Toronto, Canada: International Society for Fall Protection.

Wehner, T. 1992. Sicherheit als Fehlerfreundlichkeit. Opladen: Westdeutscher Verlag.

Zimolong, B, and L Duda. 1992. Human error reduction strategies in advanced manufacturing systems. In Human-robot Interaction, edited by M Rahimi and W Karwowski. London: Taylor & Francis.