Monday, 14 March 2011 17:21

Chemical Hazards

Rate this item
(1 Vote)

Fuel and Oils for Portable Machines

Portable forestry machines such as chain-saws, brush saws and mobile machines are sources of exhaust emissions of gasoline in logging operations. Gasoline contains mainly aromatic (including up to 5% benzene in some countries) and aliphatic hydrocarbons, additives and some impurities. During the cold season gasoline contains more lightweight and easily evaporating hydrocarbons than during warm season. Additives are organic lead compounds, alcohols and ethers which are used to increase the octane number of gasoline. In many cases, lead has been totally replaced by ethers and alcohols.

The portable machines used in forestry are powered by two-stroke engines, where lubricating oil is mixed with gasoline. Lubrication oils as well as chain oils are mineral oils, synthetic oils or vegetable oils. The exposure to gasoline and lubrication and chain oil may occur during mixing fuel and filling as well as during logging. Fuels are also a fire hazard, of course, and require careful storage and handling.

Oil aerosols may create health hazards such as irritation of the upper respiratory tract and eyes, as well as skin problems. The exposure of lumberjacks to oil aerosols was studied during manual logging. Both mineral and vegetable oils were investigated. The exposure of forestry workers to oil aerosols was on the average 0.3 mg/m3 for mineral oil and even less for vegetable oil.

The mechanization of forestry work is increasing rapidly. The machines in logging operations use large amounts of fuel oil, lubricants and hydraulic oils in their engines and hydraulic systems. During maintenance and repair operations, the hands of machine operators are exposed to lubricants, hydraulic oils and fuel oils, which may cause irritant dermatitis. Mineral oils with short-chain hydrocarbons (C14–C21) are the most irritant. To avoid irritation, the skin must be protected from oil contact by protective gloves and good personal hygiene.

 

Exhaust Gases

The main component of chain-saw exhaust gases is unburned gasoline. Usually about 30% of the gasoline consumed by a chain-saw engine is emitted unburned. The main components of exhaust emission are hydrocarbons which are typical constituents of gasoline. Aromatic hydrocarbons, particularly toluene, are usually identified among them, but even benzene is found. Some of the exhaust gases are formed during combustion, and the main toxic product among them is carbon monoxide. As a result of combustion there are also aldehydes, mainly formaldehyde, and nitrogen oxides.

The exposure of workers to exhaust gases from chain-saws has been studied in Sweden. Operator exposure to chain-saw exhaust was evaluated under various logging situations. Measurements revealed no difference in average levels of exposure when logging in the presence or in the absence of snow. The felling operation, however, results in short-term high exposure levels, especially when the operation is performed while there is deep snow on the ground. This is judged to be the main cause of the discomfort experienced by loggers. Average exposure levels for loggers engaged only in felling were twice as high as those for cutters who also perform delimbing, bucking and manual skidding of timber. The latter operations involved considerably lower exposure. Typical average levels of exposure are as follows: hydrocarbons, 20 mg/m3; benzene, 0.6 mg/m3; formaldehyde, 0.1 mg/m3; carbon monoxide, 20 mg/m3.

These values are clearly below the 8-hour occupational exposure limit values in industrialized countries. However, loggers often complain about irritation of the upper respiratory tract and eyes, headache, nausea and fatigue, which can be at least partly explained by these exposure levels.

Pesticides and Herbicides

Pesticides are used in forests and forest nurseries to control fungi, insects and rodents. The overall quantities used are typically small when compared with agricultural use. In forests herbicides are used to control hardwood brush, weeds and grass in young softwood sapling stands. Phenoxy herbicides, glyphosate or triazines are used for this purpose. For occasional needs, insecticides, mainly organophosphorus compounds, organochlorine compounds or synthetic pyredroids may also be used. In forest nurseries dithiocarbamates are used regularly to protect softwood seedlings against fungus of pines. An overview of chemicals used in Europe and North America in the 1980s is provided in table 1. Many countries have taken measures to find alternatives to pesticides or to restrict their use. For more detail on the chemistry, chemical symptoms of intoxication and treatment see the chemicals section of this Encyclopaedia.

Table 1.  Examples of chemicals used in forestry in Europe and North America in the 1980s.

Functions

Chemicals

Fungicides

Benomyl, Borax, Carbendazim, Chlorothalonil, Dicropropene, Endosulphaani, Gamma-HCH, Mancozeb, Maneb, Methyl bromide, Metiram, Thiuram, Zineb

Game control

Polyvinyl acetate

Game damage control

Thiram

Game repellents

Fish oil, tall oil

Herbicides

Allyl alcohol, Cyanazin, Dachtal, Dalapon, Dicamba, Dichlobenil, Diuron, Fosamine, Glyphosate, Hexazinone, MCPA, MCPB, Mecoprop (MCPP), MSMA, Oxyfluorten, Paraquat, Phenoxy herbicides (e.g., 2,4,5-T*, 2,4-D), Picloram, Pronoamide, Simazine, Sulphur, TCA, Terbuthiuron, Terbuthylazine, Trichlopyr, Trifluralin

Insecticides

Azinphos, Bacillus thuringiens, Bendiocarpanate, Carbaryl, Cypermethrin, Deltamethrin, Diflubenzuron, Ethylene dibromide, Fenitrothion, Fenvalerate, Lindane, Lindane+promecarb, Malathion, Parathion, Parathionmethyl, Pyrethrin, Permethrin, Propoxur, Propyzamide, Tetrachlorphinos, Trichlorfon

Pesticides

Captan, Chlorpyrifos, Diazinon, Metalyxyl, Napropamide, Sethoxydim, Traiadimefon, Sodium cyanide (rabbits)

Rodenticides

Aluminium phosphide, Strychnine, Warfarin, Zinc phosphide, Ziram

Soil sterilant

Dasomet

Stump protection

Urea

Fuels and oils

Mineral oils, synthetic oils, vegetable oils, gasoline, diesel oil

Other chemicals

Fertilizers (e.g., urea), solvents (e.g., glycol ethers, long-chain alcohols), Desmetryn

* Restricted in some countries.

Source: Adapted from Patosaari 1987.

A wide variety of techniques are used for the application of pesticides to their intended target in forests and forestry nurseries. Common methods are aerial spraying, application from tractor-driven equipment, knapsack spraying, ULV spraying and the use of sprayers connected to brush saws.

The risk of exposure is similar to that in other pesticide applications. To avoid exposure to pesticides, forestry workers should use personal protective equipment (PPE) (e.g., cap, coveralls, boots and gloves). If toxic pesticides are applied, a respiratory device should also be worn during applications. Effective PPE often leads to heat build-up and excessive sweating. Applications should be planned for the coolest hours of the day and when it is not too windy. It is also important to wash all spills immediately with water and to avoid smoking and eating during spray operations.

The symptoms caused by excessive exposure to pesticides vary greatly depending on the compound used for application, but most often occupational exposure to pesticides will cause skin disorders. (For a more detailed discussion of pesticides used in forestry in Europe and northern America see FAO/ECE/ILO 1991.)

Others

Other chemicals commonly used in forestry work are fertilizers and colourants used for timber marking. Timber marking is done either with a marking hammer or a spray bottle. The colourants contain glycol ethers, alcohols and other organic solvents, but the exposure level during the work is probably low. The fertilizers used in forestry have low toxicity, and the use of them is seldom a problem in respect of occupational hygiene.

 

Back

Read 7584 times Last modified on Wednesday, 03 August 2011 20:34

" DISCLAIMER: The ILO does not take responsibility for content presented on this web portal that is presented in any language other than English, which is the language used for the initial production and peer-review of original content. Certain statistics have not been updated since the production of the 4th edition of the Encyclopaedia (1998)."

Contents

Forestry References

Apud, E, L Bostrand, I Mobbs, and B Strehlke. 1989. Guidelines on Ergonomic Study in Forestry. Geneva: ILO.

Apud, E and S Valdés. 1995. Ergonomics in Forestry—The Chilean Case. Geneva: ILO.

Banister, E, D Robinson, and D Trites. 1990. Ergonomics of Tree Planting. Canada–British Columbia Forest Resources Development Agreement, FRDA Report 127. Victoria, BC: FRDA.

Brown, GW. 1985. Forestry and Water Quality. Corvallis, OR: Oregon State University (OSU) Book Stores Inc.

Chen, KT. 1990. Logging Accidents—An Emerging Problem. Sarawak, Malaysia: Occupational Health Unit, Medical Department.

Dummel, K and H Branz. 1986. “Holzernteverfahren,” Schriften Reihefdes Bundesministers für Ernätrung, Handwirtschaft und Forsten. Reihe A: Landwirtschafts verlag Münster-Hiltrup.

Durnin, JVGA and R Passmore. 1967. Energy, Work, Leisure. London: Heinemann.

Food and Agriculture Organization (FAO) of the United Nations. 1992. Introduction to Ergonomics in Forestry in Developing Countries. Forestry Paper 100. Rome:FAO.

—. 1995. Forestry—Statistics Today for Tomorrow. Rome: FAO.

—. 1996. FAO Model Code of Forest Harvesting Practice. Rome: FAO.

FAO/ECE/ILO. 1989. Impact of Mechanization of Forest Operations on the Soil. Proceedings of a seminar, Louvain-la-neuve, Belgium, 11–15 September. Geneva: FAO/ECE/ILO Joint Committee on Forest Technology, Management and Training.

—. 1991. The Use of Pesticides in Forestry. Proceedings of a seminar, Sparsholt, UK, 10–14 September 1990.

—. 1994. Soil, Tree, Machine Interactions, FORSITRISK. Proceedings of an interactive workshop and seminar, Feldafiraf, Germany, 4–8 July. Geneva: FAO/ECE/ILO Joint Committee on Forest Technology, Management and Training.

—. 1996a. Manual on Acute Forest Damage. UN/ECE/ FAO discussion papers ECE/TIM/DP/7, New York and Geneva: Joint FAO/ECE/ILO Committee on Forest Technology, Management and Training.

—. 1996b. Skills and Training in Forestry—Results of a Survey of ECE Member Countries. Geneva: FAO/ECE/ILO Joint Committee on Forest Technology, Management and Training.

FAO/ILO. 1980. Chainsaws in Tropical Forests. Forest Training Series No. 2. Rome: FAO.

Gellerstedt, S. 1993. Work and Health in Forest Work. Göteborg: Chalmers University of Technology.

Giguère, D, R Bélanger, J-M Gauthier, and C Larue. 1991. Étude préliminaire du travail de reboisement. Rapport IRSST B-026. Montreal: IRSST.

—. 1993. Ergonomics aspects of tree planting using multi-pot technology. Ergonomics 36(8):963-972.

Golsse, JM. 1994. Revised FERIC Ergonomic Checklist for Canadian Forest Machinery. Pointe Claire: Forest Engineering Research institute of Canada.

Haile, F. 1991. Women Fuelwood Carriers in Addis Ababa and the Peri-urban Forest. Research on women in fuelwood transport in Addis Ababa, Ethiopia ETH/88/MO1/IRDC and ETH/89/MO5/NOR. Project report. Geneva: ILO.

Harstela, P. 1990. Work postures and strain of workers in Nordic forest work: A selective review. Int J Ind Erg 5:219–226.

International Labour Organization (ILO). 1969. Safety and Health in Forestry Work. An ILO Code of Practice. Geneva: ILO.

—. 1988. Maximum Weights in Load Lifting and Carrying. Occupational Safety and Health Service, No. 59. Geneva: ILO.

—. 1991. Occupational Safety and Health in Forestry. Report II, Forestry and Wood Industries Committee, Second Session. Geneva: ILO.

—. 1997. Code of Practice on Safety and Health in Forest Work. MEFW/1997/3. Geneva: ILO.

—. 1998. Code of Practice on Safety and Health in Forest Work. Geneva: ILO.

International Standards Organization (ISO). 1986. Equipment for Working the Soil: ROPS—Laboratory Testing and Performance Specifications. ISO 3471-1. Geneva: ISO.

Jokulioma, H and H Tapola. 1993. Forest worker safety and health in Finland. Unasylva 4(175):57–63.

Juntunen, ML. 1993. Training of harvester operations in Finland. Presented in seminar on the use of multifunctional machinery and equipment in logging operations. Olenino Logging Enterprise, Tvor Region, Russian Federation 22–28 August.

—. 1995. Professional harvester operator: Basic knowledge and skills from training—Operating skills from working life? Presented in IUFRO XX World Congress, Tampre, Finland, 6–12 August.

Kanninen, K. 1986. The occurrence of occupational accidents in logging operations and the aims of preventive measures. In the proceedings of a seminar on occupational health and rehabilitation of forest workers, Kuopio, Finland, 3–7 June 1985. FAO/ECE/ILO Joint Committee on Forest Working Techniques and Training of Forest Workers.

Kastenholz, E. 1996. Sicheres Handeln bei der Holzernteuntersuchung von Einflüssen auf das Unfallgeschehen bei der Waldarbeit unter besonderer Berücksichtigung der Lohnform. Doctoral dissertation. Freiburg, Germany: University of Freiburg.

Kantola, M and P Harstela. 1988. Handbook on Appropriate Technology for Forestry Operations in Developing Counties, Part 2. Forestry Training Programme Publication 19. Helsinki: National Board of Vocational Education.

Kimmins, H. 1992. Balancing Act—Environmental Issues in Forestry. Vancouver, BC: University of British Columbia Press.

Lejhancova, M. 1968. Skin damage caused by mineral oils. Procovni Lekarstvi 20(4):164–168.

Lidén, E. 1995. Forest Machine Contractors in Swedish Industrial Forestry: Significance and Conditions during 1986–1993. Department of Operational Efficiency Report No. 195. Swedish University of Agricultural Science.

Ministry of Skills Development. 1989. Cutter-skidder Operator: Competency-based Training Standards. Ontario: Ministry of Skills Development.

Moos, H and B Kvitzau. 1988. Retraining of adult forest workers entering forestry from other occupation. In Proceedings of Seminar on the Employment of Contractors in Forestry, Loubières, France 26-30 September 1988. Loubiéres: FAO/ECE/ILO Joint Committee on Forest Work Techniques and Training of Forest Workers.

National Proficiency Test Council (NPTC) and Scottish Skill Testing Service (SSTS). 1992. Schedule of Chainsaw Standards. Warwickshire, UK: NPTC and SSTS.

—. 1993. Certificates of Competence in Chainsaw Operation. Warwickshire, United Kingdom: National Proficiency Tests Council and Scottish Skills Testing Service.

Patosaari, P. 1987. Chemicals in Forestry: Health Hazards and Protection. Report to the FAO/ECE/ILO Joint Committee on Forest Working Technique and Training of Forest Workers, Helsinki (mimeo).

Pellet. 1995. Rapport d’étude: L’ánalyse de l’áccident par la méthode de l’arbre des causes. Luzern: Schweizerische Unfallversicherungsanstalt (SUVA) (mimeo).

Powers, RF, DH Alban, RE Miller, AE Tiarks, CG Wells, PE Avers, RG Cline, RO Fitzgerald, and JNS Loftus. 1990.
Sustaining site productivity in North American forests: Problems and prospects. In Sustained Productivity of Forest Soils, edited by SP Gessed, DS Lacate, GF Weetman and RF Powers. Vancouver, BC: Faculty of Forestry Publication.

Robinson, DG, DG Trites, and EW Banister. 1993. Physiological effects of work stress and pesticides exposure in tree planting by British Columbian silviculture workers. Ergonomics 36(8):951–961.

Rodero, F. 1987. Nota sobre siniestralidad en incendios forestales. Madrid, Spain: Instituto Nacional para la Conservación de la Naturaleza.

Saarilahti, M and A Asghar. 1994. Study on winter planting of chir pine. Research paper 12, ILO project, Pakistan.
Skoupy, A and R Ulrich. 1994. Dispersal of chain lubrication oil in one-man chain-saws. Forsttechnische Information 11:121–123.

Skyberg, K, A Ronneberg, CC Christensen, CR Naess-Andersen, HE Refsum, and A Borgelsen. 1992. Lung function and radiographic signs of pulmonary fibrosis in oil exposed workers in a cable manufacturing company: A follow up study. Brit J Ind Med 49(5):309–315.

Slappendel, C, I Laird, I Kawachi, S Marshal, and C Cryer. 1993. Factors affecting work-related injury among forestry workers: A review. J Saf Res 24:19–32.

Smith, TJ. 1987. Occupational characteristics of tree-planting work. Sylviculture Magazine II(1):12–17.

Sozialversicherung der Bauern. 1990. Extracts from official Austrian statistics submitted to the ILO (unpublished).

Staudt, F. 1990. Ergonomics 1990. Proceedings P3.03 Ergonomics XIX World Congress IUFRO, Montreal, Canada, August 1990. The Netherlands: Department of Forestry, Section Forest Technique and Woodscience, Wageningen Agricultural University.

Stjernberg, EI. 1988. A Study of Manual Tree Planting Operations in Central and Eastern Canada. FERIC technical report TR-79. Montreal: Forest Engineering Research Institute of Canada.

Stolk, T. 1989. Gebruiker mee laten kiezen uit persoonlijke beschermingsmiddelen. Tuin & Landschap 18.

Strehlke, B. 1989. The study of forest accidents. In Guidelines on Ergonomic Study in Forestry, edited by E Apud. Geneva: ILO.

Trites, DG, DG Robinson, and EW Banister. 1993. Cardiovascular and muscular strain during a tree planting season among British Columbian silviculture workers. Ergonomics 36(8):935–949.

Udo, ES. 1987. Working Conditions and Accidents in Nigerian Logging and Sawmilling Industries. Report for the ILO (unpublished).

Wettman, O. 1992. Securité au travail dans l’exploitation forestière en Suisse. In FAO/ECE/ILO Proceedings of Seminar on the Future of the Forestry Workforce, edited by FAO/ECE/ILO. Corvallis, OR: Oregon State University Press.